| Model | LP-100-512 |
| Frequency (manufacturer model field) | 100-512MHz |
| Bandwidth (manufacturer model field) | 100-512MHz |
| Gain (manufacturer model field) | 9 dBi |
| Frequency Range | 100-512 MHz |
| Gain | 9 dBi |
| Bandwidth | Entire Band |
| Polarization | Vertical or Horizontal |
| Input Impedance | 50 Ohms |
| Radiation Pattern | Directional |
| Horizontal Beamwidth -Half Power Points | 60 Degrees |
| Front to Back Ratio | 18 dB |
| VSWR - Equal To or Better Then | 2.2:1 |
| RF Power Handling Capacity | 400 Watts @500MHz |
| Input Termination | N-Female |
| Lightning Protection | Direct Ground |
| Antenna Materials | 6063T6 Aluminium Alloy |
| Mounting Hardware -Materials | Marine Grade Stainless Steel |
| Wind Rating | 200 Km/Hr. |
| Overall Length | 1.50 Meters |
| Shipping Length | 1.55 Meters |
| Support Boom -Material - O.D. | AluminumSquare Tube |
| Elements - Materials- Cross Section - Outer Diameter | AluminumRound Tube |
| Insulator Material | Teflon & Nylon |
| Maximum Mount Pipe Diameter | 38-77mm (1.5 to 3 Inches) |
| Gross Weight | 6 Kgs. |
| Operating Temperature | (-) 30 to +70 Degrees Celsius |
| Storage Temperature | (-) 40 to +80 Degrees Celsius |
| Humidity | 0 to 95% RH |
| Published detail | The LP-100-512 is optimized for operators who require gapless frequency coverage from 100 MHz to 512 MHz without the logistical complexity of swapping antennas. |
| Non-Loaded Efficiency | By avoiding lossy electrical loading, the LP-100-512 maintains maximum radiation efficiency and a consistent 9 dBi gain. This ensures that every watt of the 400W power capacity is projected toward the target. |
| Rapid Single-Tool Assembly | Designed for high-mobility "jump" missions, the antenna can be fully assembled with a single spanner in less than 5 minutes. The foldable elements and stainless steel stud system streamline logistics in the field. |
| Streamlined Cable Management | The coaxial cable is routed internally through the support boom and exits at the rear end. This prevents cable snagging during deployment and ensures the feedline remains shielded from environmental wear. |
| Marine-Grade Durability | All fasteners (screws, nuts, and bolts) are made of Type 316 marine-grade stainless steel. The entire array is protected by an epoxy-based paint finish to withstand saline coastal air and high-humidity environments. |
| Integrated Safety | Operates at D.C. ground, providing a low-resistance discharge path for lightning and suppressing atmospheric static to ensure an ultra-quiet noise floor during sensitive SIGINT operations. |
| Mechanical Stability | Extra spacers between the 25mm square booms and a high wind rating of 200 km/hr ensure the antenna remains operational in severe weather conditions. |
| Elite 100–512 MHz Coverage | Replaces multiple dedicated antennas for VHF High and UHF bands. |
| High-Efficiency 9 dBi Gain | Focused directional precision for long-range aeronautical and ground intercepts. |
| Fast 5-Minute Assembly | One-spanner setup for rapid-deployment mobile and tactical missions. |
| Polarization Agility | Permits quick orientation changes between Vertical and Horizontal modes. |
| Rear-End Coaxial Exit | Protects the feedline and maintains pattern integrity. |
| Published detail | In the signal-dense 100-512 MHz band, isolating specific tactical or aviation links requires a surgical directional focus. |
| The Precision Advantage | The focused 70-degree beamwidth acts as a directional "spotlight." This allows an operator to isolate a specific target while physically "nulling out" interference from the sides and rear. |
| The 9 dBi Advantage | The focused 70-degree horizontal beamwidth of the LP-100-512 acts as an RF "spotlight." This allows an operator to isolate a specific aircraft's transmission or a distant tactical repeater while physically "nulling out" interference from the sides and rear. |
| Range Extension | Every 6 dB of gain effectively doubles your reception range. With 9 dBi, this antenna can pull in weak tactical signals from distances where standard dipole antennas would only see static. |
| Published detail | UHF signals (above 300 MHz) reflect sharply off glass, metal, and concrete. Each reflection can cause the signal's polarization to shift—a phenomenon known as Polarization Rotation. |
| The "Null" Problem | Most tactical handhelds and vehicle whips are vertically polarized. If a signal reflects off a slanted roof or metal structure, it may arrive at your site with a significant horizontal shift. A standard vertical antenna would experience a signal dropout of up to 20 dB. |
| The Tactical Solution | The LP-100-512 features a flexible mounting arrangement that allows operators to switch between Horizontal and Vertical polarization in seconds. This ensures you can match the orientation of the incoming reflected wave to maintain a stable, high-fidelity intercept. |
| Published detail | To successfully disrupt a target link (e.g., a 400 MHz emergency services net or an aviation command link), you must achieve a superior Jamming-to-Signal (J/S) ratio at the victim’s receiver. |
| Published detail | 400W Continuous Power: The LP-100-512 acts as a powerful directional "floodlight." Its 9 dBi gain acts as an RF magnifying glass, concentrating 400 Watts of energy into a focused 70-degree cone. |
| ERP Advantage | This concentration exponentially increases your Effective Radiated Power (ERP). You can successfully "drown out" a legitimate signal from several kilometers away, even when the adversary is using high-power mobile transmitters. |
| The Solution | The LP-100-512 is D.C. Grounded. It constantly bleeds off this static charge to the mast and earth. This ensures the lowest possible noise floor, allowing you to detect low-power "hidden" transmissions or frequency-hopping signals that would be buried in the static of an ungrounded antenna. |
| Rapid 5-Minute Setup | Take full advantage of the one-spanner assembly. In modern EW, the ability to pack up and move (Shoot-and-Scoot) is vital to avoid detection by enemy direction-finding units. |
| Cable Integrity | In the 500 MHz range, cable loss becomes significant. Avoid standard RG-58. Use LMR-400 or LMR-600. Every 3 dB of cable loss effectively cuts your jamming power or reception sensitivity in half. |
| Mast Stability | At 5.5 Kgs and 1.5 meters long, this antenna requires a stable mast (up to 2.5 inches). A swaying mast will cause the 70-degree beam to "shimmer," making it harder to maintain a lock on a distant target. |
| Boresight Alignment | Because the beamwidth is 70 degrees, a 35-degree error in alignment will drop your gain significantly. Use a compass to ensure the antenna is pointed exactly at the target sector for maximum intercept probability. |
| Frequency stated in title | 100-512 MHz |
| Gain stated in title | 9 dBi |
| Category | Horn, Dish, Grid & Log Periodic |