| Model | LPDS-200-500 |
| Frequency (manufacturer model field) | 200-500MHz |
| Bandwidth (manufacturer model field) | 200-500MHz |
| Gain (manufacturer model field) | 14 dBi |
| Frequency Range | 200-500 MHz |
| Gain | 14 dBi |
| Bandwidth | 200-500MHz |
| Polarization | Vertical or Horizontal |
| Input Impedance | 50 Ohms |
| Beamwidth -3dB. | 25 Degrees - Azimuth |
| Beamwidth -3dB. | 50 Degrees - Elevation |
| Front to Back Ratio | 18 dB. |
| VSWR - Equal To or Better Then | < 2.5:1 |
| RF Power Handling Capacity | 500 Watts |
| Input Termination | N-Female |
| Lightning Protection | Direct Ground |
| Antenna Materials | 6063T6 Aluminium & ABS |
| Mounting Hardware -Materials | Stainless Steel |
| Wind Rating | 200 Km/Hr. |
| Overall Length | 1.4 Meters |
| Shipping Length | 1.5 Meters |
| Radiating Material | 6063T6 Aluminum Alloy |
| Mounting Clamps Position | At Rear End of Support Boom |
| Maximum Mount Pipe Diameter | 38-62 mm (1.5-2.25 Inches) |
| Gross Weight | 20 Kgs. |
| Operating Temperature | (-) 30 to +70 Degrees Celsius |
| Storage Temperature | (-) 40 to +80 Degrees Celsius |
| Humidity | 0 to 95% RH |
| Stacking Advantage | By combining two LPDA units with a specialized power splitter/combiner and phasing harness, the system narrows the horizontal beam to a surgical 26 degrees. This results in a 14 dBi gain, essentially quadrupling the effective power density compared to a single-bay antenna. |
| Precision Beam Steering | The tight beamwidth allows for exceptional spatial filtering, enabling operators to "lock onto" a specific aircraft or signal source while completely ignoring interference from neighboring channels or reflective obstacles. |
| Rapid Tactical Logistics | Despite its dual-array complexity, the system is designed for mobility. The foldable/removable elements and segmented booms allow for full assembly in less than 10 minutes by a tactical team. |
| MIL-STD-810G Certified | Rigorously tested for extreme temperature (-40 to +80°C), shock, vibration, and salt fog. It is specifically engineered to thrive in coastal, monsoon, or desert environments. |
| Marine-Grade Hardening | All fasteners and mounting hardware are made of Type 316 marine-grade stainless steel. The entire array is protected by an electrostatic Epoxy Powder Coating for total corrosion resistance. |
| D.C. Grounded Safety | Operates at D.C. ground, providing a low-resistance path for lightning and suppressing atmospheric static to ensure an ultra-quiet noise floor for high-sensitivity surveillance. |
| Elite 14 dBi High Gain | Surgical directional precision for ultra-long-range intercepts. |
| Narrow 26° Horizontal Beamwidth | Eliminates co-channel interference in congested UHF bands. |
| Complete Stacking Kit | Includes phasing harness, power splitter, and horizontal stacking poles. |
| Fast 10-Minute Assembly | Optimized for rapid-deployment mobile and tactical missions. |
| Center-Mast Mounting | Securely fits 52mm to 75mm (2-3 inch) heavy-duty masts. |
| Anti-Corrosion Finish | Olive Green epoxy coating for tactical low-visibility and salt protection. |
| The Stacked Benefit | The 26-degree beamwidth acts as an RF "telescope," focusing energy toward the flight corridor and providing a 20 dB Front-to-Back ratio to prevent self-interference from on-site equipment. |
| Beam Compression | By placing two antennas side-by-side and feeding them in-phase, the horizontal beamwidth is compressed to a razor-sharp 26 degrees. This results in a 14 dBi gain, allowing an operator to project four times the effective power (ERP) toward a target compared to a single-bay antenna. |
| Spatial Filtering | The narrow 26-degree beam allows you to "isolate" a specific aircraft or ground station in a high-density environment, physically "nulling out" interference from nearby transmitters that are only a few degrees off-boresight. |
| Published detail | The 200–500 MHz range is the primary home for military aviation. Signals from high-altitude aircraft can be weak and subject to "fading" as the aircraft moves. |
| High-Gain Sensitivity | The 14 dBi gain acts as a massive "ear," pulling in low-power aeronautical transmissions from hundreds of kilometers away. This provides SIGINT teams with an extended "Early Warning" window. |
| Triangulation Accuracy | Because the beam is so narrow, the "bearing" of a detected signal is much more accurate. This allows for superior triangulation of mobile aerial assets when used in conjunction with a second intercept site. |
| Published detail | To successfully disrupt a target link (e.g., a 300 MHz tactical SATCOM or an ATC command link), you must achieve a superior Jamming-to-Signal (J/S) ratio at the victim’s receiver. |
| Front-to-Back Isolation | The 20 dB Front-to-Back ratio ensures that the massive power being projected forward does not "bleed" backward into your own team's sensitive SIGINT receivers or command-and-control links. |
| The Solution | The LPDS-200-500 is D.C. Grounded. It constantly bleeds off this static charge to the mast and earth. This ensures the lowest possible noise floor, allowing you to detect low-power "hidden" transmissions or frequency-hopping signals that would be buried in the static of an ungrounded system. |
| Phasing Harness Integrity | The system relies on the phasing harness cables and power splitter to ensure both antennas "fire" at the exact same time. Ensure these cables are equal in length and the connectors are torqued to spec; a timing error of just a few millimeters can distort the 26-degree beam. |
| Mast Stability | At 15 Kgs and with a dual-bay wind profile, this system requires a heavy-duty, guyed mast (up to 3 inches). A swaying mast will cause the narrow 26-degree beam to "shimmer," making it difficult to maintain a lock on a distant target. |
| Polarization Matching | While ATC is usually vertical, reflections in urban or mountainous areas rotate signals. The LPDS-200-500 kit allows for rapid switching between Vertical and Horizontal polarization—always match the target's peak signal strength for maximum intercept success. |
| High-Power Cable Selection | When running at 1.5KW, use LMR-600 or corrugated copper feeders. Standard cables will suffer dielectric breakdown or overheat, leading to catastrophic VSWR failure. |
| Frequency stated in title | 200-500 MHz |
| Gain stated in title | 14 dBi |
| Category | Horn, Dish, Grid & Log Periodic |