| Model | LPDP-20-500 |
| Frequency (manufacturer model field) | 20-500MHz |
| Bandwidth (manufacturer model field) | 20-500MHz |
| Gain (manufacturer model field) | 7 dBi. |
| Frequency Range | 20 - 500 MHz. |
| Gain | 7 dBi. |
| Bandwidth | Entire Band |
| Polarization | Vertical & Horizontal |
| Input Impedance | 50 Ohms |
| Radiation Pattern | Directional |
| Beamwidth -3dB. | 120 +/- 15 Degrees (Horizontal) |
| Front to Back Ratio | 14 +/- 2 dB. |
| VSWR - Equal To or Better Then | 2.5:1 |
| RF Power Handling Capacity | 500 Watts |
| Input Termination | 2 x N-Female |
| Lightning Protection | DC Ground |
| Antenna Materials | All Aluminum |
| Mounting Hardware -Materials | Stainless Steel |
| Wind Rating | 170 Km/Hr. |
| Overall Length | 6 Meters |
| Shipping Length | 3 Meters |
| Support Boom -Material - O.D. | AluminumSquare Tube |
| Elements - Materials- Cross Section - Outer Diameter | AluminumRound Tube |
| Insulator Material | Teflon & Nylon |
| Maximum Mount Pipe Diameter | 50-76 mm (2-3 Inches) |
| Gross Weight | 70 Kgs. |
| Operating Temperature | (-)30 to + 70 Degrees Celsius |
| Storage Temperature | (-)40 to + 80 Degrees Celsius |
| Humidity | 0 to 95% RH |
| True Polarization Diversity | Equipped with 2 x N-Female input ports, the antenna eliminates "polarization fading" by concurrently processing vertical and horizontal signal components. This is vital for intercepting tactical radios in dense foliage or signals reflecting off complex terrain. |
| Unloaded Efficiency | To maintain peak radiation efficiency, the LPDP-20-500 uses full-sized radiating elements (up to 3.75 meters). This avoids the heat and power loss common in size-reducing loading techniques, ensuring a consistent 8 dBi gain across 95% of the 20-500 MHz band. |
| Rapid Field Deployment | Despite its 6-meter (20-foot) length, the antenna features a fast deployment self-locking device. Two operators can fully assemble the array within 10 minutes using simple hand tools, making it ideal for temporary tactical sites. |
| Foldable Tactical Elements | Elements are supplied in two segments to facilitate manageable shipping. The support booms are reinforced with extra spacers to withstand wind speeds up to 170 Km/Hr. |
| Integrated Protection | The entire array operates at D.C. ground, providing a low-resistance path for lightning protection and suppressing atmospheric static for a high-sensitivity "quiet" noise floor. |
| Marine-Grade Durability | All fasteners, screws, and bolts are made of Type 316 marine-grade stainless steel, ensuring total corrosion resistance in coastal or high-humidity environments. |
| Dual-Polarized Cross-Element Geometry | Simultaneous capture of E & H polarized signals for zero-loss intercepts. |
| Massive 20–500 MHz Bandwidth | Covers Strategic HF, Tactical VHF, and Military UHF in one unit. |
| High-Power 500W Rating | Engineered for high-duty cycle electronic countermeasures (ECM). |
| Strategic 6-Meter Design | Optimized for low-frequency efficiency without lossy electrical loading. |
| Direct D.C. Grounding | Superior lightning protection and suppressed noise for SIGINT applications. |
| Fast-Deployment Self-Locking Elements | Quick assembly for rapid tactical maneuvering. |
| Marine Grade 316 Stainless Hardware | Resists coastal, industrial, and tropical corrosion. |
| Balanced Center Mounting | Securely fits 50mm to 76mm (2-3 inch) heavy-duty mounting pipes. |
| The Solution | By monitoring both ports simultaneously, the LPDP-20-500 captures the signal on the horizontal plane even when it disappears on the vertical, maintaining a stable link or intercept. |
| Published detail | To successfully jam frequency-hopping targets in the 20–500 MHz band, you must saturate the victim's receiver regardless of their antenna orientation. |
| Published detail | In the lower frequencies (20–88 MHz), tactical communications rely heavily on vertical whips. However, as these signals travel through dense forests or urban "canyons," they bounce and rotate. |
| The Problem | A standard vertical antenna can experience a signal drop of up to 20–30 dB if the incoming wave rotates horizontally. In a jamming scenario, this means your interference might not even reach the target's receiver. |
| The LPDP-20-500 Solution | By using both the Vertical and Horizontal ports, you create a "circular-like" reception/transmission field. If the signal fades on the vertical plane, the horizontal elements pick up the slack, ensuring a 100% intercept rate. |
| Dual-Plane Saturation | Many modern high-end radios use diversity antennas to "dodge" jammers. By feeding 500 Watts into both ports of the LPDP-20-500, you saturate both the E (Electric) and H (Magnetic) planes. This leaves the target radio with no "clean" orientation to receive data. |
| Directional Power Density | The 8 dBi gain concentrates that 500W into a 110-degree floodlight. This dramatically increases the Jamming-to-Signal (J/S) ratio compared to an omnidirectional antenna, allowing you to jam targets at significantly greater distances. |
| Vertical Dominance | Confirms mobile tactical units, maritime vessels, or standard ground-based infantry whips. |
| Horizontal Dominance | Indicates fixed-site point-to-point relays, TV/Broadcast backup links, or specialized NVIS (Near Vertical Incidence Skywave) links used for regional communication over mountainous terrain. |
| Rapid Polarization Shifting | A signal that rapidly moves between V and H ports often identifies a moving vehicle or aircraft as the signal bounces off changing terrain. |
| The 15 dB Shield | The LPDP-20-500 radiates 15 dB less energy out of the back than the front. This allows your EW team to operate their own Command & Control (C2) equipment directly behind the antenna without being blinded by their own jammer. |
| Feeder Management | Use high-quality, phase-matched LMR-600 or 1/2" corrugated cables. At 500 MHz, cable loss becomes significant; keep runs as short as possible to ensure all 500W reaches the elements. |
| Mast Stability | Due to the 7.5-meter width and 70 kg weight, use a heavy-duty 76mm (3-inch) steel or reinforced aluminum mast. Ensure the center-mount clamp is torqued correctly to prevent "spinning" in high winds. |
| Grounding for Noise Floor | Ensure the mast is grounded. The D.C. Grounded design of the LPDP-20-500 is only effective if it has a low-resistance path to earth to bleed off the atmospheric static that can drown out weak SIGINT signals. |
| Rapid Setup | Take advantage of the self-locking device. With two operators, the assembly can be completed in under 10 minutes. Always check element alignment before raising the mast to ensure the cross-polarization discrimination remains above 25 dB. |
| Frequency stated in title | 20-500 MHz |
| Gain stated in title | 8 dBi |
| Category | Horn, Dish, Grid & Log Periodic |