| Model | LP-600-1000 |
| Frequency (manufacturer model field) | 600-1000MHz |
| Bandwidth (manufacturer model field) | 600-1000MHz |
| Gain (manufacturer model field) | 12 dBi |
| Frequency Range | 600-1000 MHz |
| Gain | 12 dBi |
| Bandwidth | 600-1000MHz |
| Polarization | Vertical or Horizontal |
| Input Impedance | 50 Ohms |
| Radiation Pattern | Directional |
| Horizontal Beamwidth -Half Power Points | 50 Degrees |
| Front to Back Ratio | 17 dB |
| VSWR - Equal To or Better Then | 1:2.5 |
| RF Power Handling Capacity | 250 Watts |
| Input Termination | N-Female |
| Lightning Protection | Direct Ground |
| Antenna Materials | 6063T6 Aluminum Alloy |
| Mounting Hardware -Materials | Marine Grade Stainless Steel |
| Overall Length | 600 mm |
| Shipping Length | 650 mm |
| Support Boom -Material - O.D. | AluminumSquare Tube |
| Elements - Materials- Cross Section - Outer Diameter | AluminumRound Rod |
| Maximum Mount Pipe Diameter | 52mm (2 Inches) |
| Gross Weight | 2 Kgs. |
| Operating Temperature | (-) 30 to +75 Degrees Celsius |
| Storage Temperature | (-) 40 to +85 Degrees Celsius |
| Humidity | 0 to 95% RH |
| Elite 12 dBi Gain | By utilizing a full-sized, non-loaded array design, the antenna achieves exceptional gain and a focused 50-degree beamwidth. This allows for extreme precision in signal targeting and significantly increased range compared to standard broadband antennas. |
| Rear-End Master Mounting | The mounting bracket is welded at the back end of the dual booms. This "rear-mount" design ensures the antenna can be attached to a standard 52mm (2-inch) metal mast without the mast interfering with the radiation pattern, gain, or front-to-back ratio. |
| Weatherproof Integrated Feed | The coaxial cable is sealed inside the support boom to prevent moisture ingress, ensuring long-term reliability. The N-Female termination is conveniently located at the rear for easy integration. |
| Marine-Grade Durability | All fasteners, including screws, nuts, and bolts, are made of marine-grade stainless steel. The entire unit is finished with a protective powder coating, providing superior resistance against salt spray and corrosive saline air in coastal regions. |
| Integrated D.C. Grounding | The system operates at D.C. ground, providing a low-resistance path for lightning protection and suppressing atmospheric static for a high-sensitivity "quiet" noise floor during SIGINT operations. |
| Rugged Mechanical Stability | Extra spacers between the support booms improve mechanical durability, allowing the antenna to withstand wind loads up to 200 Km/Hr. |
| Elite 12 dBi High Gain | Focused 50-degree beamwidth for superior directional precision. |
| Comprehensive 600–1000 MHz Bandwidth | Covers LTE, GSM, and Military UHF bands. |
| Rear-Mounting Agility | Permits quick polarization changes (Vertical to Horizontal) without mast interference. |
| All-Aluminum 6063T6 Build | Lightweight (2 Kgs) yet capable of withstanding extreme environments. |
| Marine Grade Hardware | Total corrosion resistance for naval and coastal use. |
| D.C. Grounded Safety | Integrated lightning protection and enhanced noise immunity. |
| Sealed Internal Cable | Weatherproof design for maintenance-free operation.Integration Guide: Maximizing UHF Intercepts |
| Published detail | The 600-1000 MHz range is home to some of the most critical public safety and cellular bands globally. |
| The Advantage | The focused 50-degree beamwidth of the LP-600-1000 allows an operator to isolate a specific cell tower or tactical repeater in a crowded urban environment, reducing "background noise" from neighboring transmitters. |
| Published detail | At 0.6–1.0 GHz, the environment is often "RF-congested." A standard wideband antenna sees everything, which can overwhelm a receiver with background noise. |
| The Precision Advantage | The 12 dBi gain and tight 50-degree beamwidth of the LP-600-1000 act as an RF "spotlight." This allows an operator to isolate a specific cell tower or a single tactical repeater while physically "nulling out" interference coming from the sides or rear. |
| Increased Range | Every 6 dB of gain effectively doubles your reception range. With 12 dBi, this antenna can pull in weak tactical signals from distances where standard dipole antennas would only see static. |
| The "Null" Problem | Most tactical handhelds and vehicle whips are vertically polarized. If a signal reflects off a slanted roof, it may arrive at your site with a significant horizontal component. A standard vertical antenna would experience a signal dropout of up to 20 dB. |
| The Tactical Solution | The LP-600-1000 features a flexible mounting arrangement that allows operators to switch between Horizontal and Vertical polarization in seconds. This ensures you can match the orientation of the incoming reflected wave to maintain a stable, high-fidelity intercept. |
| Published detail | To successfully disrupt a target link (e.g., an 800 MHz trunked radio system), you must achieve a superior Jamming-to-Signal (J/S) ratio at the victim's receiver. |
| Power Density Focus | Instead of scattering 250W in all directions, the LP-600-1000 focuses that energy into a concentrated 50-degree cone. |
| ERP Advantage | This focuses the energy so intensely that it exponentially increases your Effective Radiated Power (ERP). You can successfully "drown out" a legitimate signal from several kilometers away, even when the adversary is using high-power mobile transmitters. |
| The Solution | The LP-600-1000 is D.C. Grounded. It constantly bleeds off static charge to the mast and earth. This ensures the lowest possible noise floor, allowing you to detect low-power "hidden" transmissions or frequency-hopping signals that would be buried in the static of an ungrounded antenna. |
| Rear-Mount Advantage | Since the mount is at the rear, you can use a standard metal mast without worrying about it distorting your signal. Ensure the mast is at least 52mm (2 inches) in diameter for stability. |
| Coaxial Integrity | At 1000 MHz (1 GHz), cable loss begins to impact performance. Use LMR-400 for cable runs over 15 meters to ensure all 250W of jamming power reaches the elements. |
| Boresight Alignment | Because the beamwidth is only 50 degrees, a 25-degree error in pointing will drop your gain by 3 dB. Use a compass to align the antenna precisely with the target sector. |
| Weather-Sealing | The internal cable is sealed, but the N-Female connection is a potential failure point. Use professional butyl rubber tape to create a moisture-proof seal. At 1 GHz, moisture in a connector will cause immediate VSWR spikes. |
| Frequency stated in title | 600-1000 MHz |
| Gain stated in title | 12 dBi |
| Category | Horn, Dish, Grid & Log Periodic |