| Model | LP-300-2500 |
| Frequency (manufacturer model field) | 300-2500MHz |
| Bandwidth (manufacturer model field) | 300-2500MHz |
| Gain (manufacturer model field) | 9 dBi |
| Frequency Range | 300-2500 MHz |
| Gain | 9 dBi |
| Bandwidth | 300-2500MHz |
| Polarization | Vertical or Horizontal |
| Input Impedance | 50 Ohms |
| Radiation Pattern | Directional |
| Horizontal Beamwidth -Half Power Points | 65+/-5 Degrees |
| Front to Back Ratio | 17+/-1 dB. |
| VSWR - Equal To or Better Then | 1:2.5 |
| RF Power Handling Capacity | 250 Watts |
| Input Termination | N-Female |
| Lightning Protection | Direct Ground |
| Antenna Materials | 6063T6 Aluminum Alloy |
| Mounting Hardware -Materials | Marine Grade Stainless Steel |
| Wind Rating | 200 Km/Hr. |
| Overall Length | 700 mm |
| Shipping Length | 800 mm |
| Support Boom -Material - O.D. | AluminumSquare Tube |
| Elements - Materials- Cross Section - Outer Diameter | AluminumRound Rod |
| Insulator Material | Teflon & Nylon |
| Mounting Clamps Position | At the back end of support boom |
| Maximum Mount Pipe Diameter | 52mm (2 Inches) |
| Gross Weight | 3.5 Kgs. |
| Operating Temperature | (-)30 to +70 Degrees Celsius |
| Storage Temperature | (-)40 to +80 Degrees Celsius |
| Humidity | 0 to 95% RH |
| Published detail | The LP-300-2500 is optimized for the signal-dense spectrum between 0.3 GHz and 2.5 GHz, where directional accuracy is paramount. |
| Elite 9 dBi Gain | By utilizing a full-sized, non-loaded array design, the antenna achieves exceptional gain and a focused 65-degree horizontal beamwidth. This allows for extreme precision in signal targeting and significantly increased range compared to standard broadband antennas. |
| Rear-End Master Mounting | The mounting bracket is welded at the back end of the dual booms. This "rear-mount" design ensures the antenna can be attached to a standard 51mm (2-inch) mast without the mast physically interfering with the radiation pattern or gain. |
| Weatherproof Integrated Feed | The coaxial cable is sealed inside the support boom to prevent moisture ingress, ensuring long-term reliability in humid or rainy environments. |
| Marine-Grade Durability | All fasteners, including screws, nuts, and bolts, are made of marine-grade stainless steel. The entire unit is finished with a protective powder coating, providing superior resistance against salt spray and corrosive saline air in coastal regions. |
| Direct D.C. Grounding | The system operates at D.C. ground, providing a low-resistance path for lightning protection and suppressing atmospheric static for a high-sensitivity "quiet" noise floor during sensitive SIGINT operations. |
| Rugged Mechanical Stability | Extra spacers between the support booms improve mechanical durability, allowing the antenna to withstand wind loads up to 200 Km/Hr. |
| Elite 9 dBi High Gain | Focused 65-degree beamwidth for superior directional precision. |
| Ultra-Wideband 300–2500 MHz Coverage | Replaces multiple antennas for UHF, GSM, and LTE. |
| Rear-Mounting Agility | Permits quick polarization changes (Vertical to Horizontal) without mast interference. |
| All-Aluminum 6063T6 Build | Lightweight (3.5 Kgs) yet capable of withstanding extreme environments. |
| Marine Grade Hardware | Total corrosion resistance for naval and coastal use. |
| Direct Ground Safety | Integrated lightning protection and enhanced noise immunity. |
| Compact Logistics | Overall length of 700mm (27.5 inches) for easy transport and handling. |
| Published detail | The 300-2500 MHz range is home to most global cellular and tactical data links. |
| The Advantage | The focused 65-degree beamwidth of the LP-300-2500 allows an operator to isolate a specific cell tower or tactical repeater in a crowded urban environment, reducing "background noise" from neighboring transmitters. |
| Published detail | In the 300–2500 MHz band, the RF environment is often "congested." A standard wideband antenna sees everything, which can overwhelm a receiver with background noise. |
| The Precision Advantage | The 9 dBi gain and focused 65-degree horizontal beamwidth of the LP-300-2500 act as an RF "spotlight." This allows an operator to isolate a specific cell tower or a single tactical repeater while physically "nulling out" interference coming from the sides or rear. |
| Range Extension | Every 6 dB of gain effectively doubles your reception range. The 9 dBi gain allows you to pull in weak tactical signals from distances where standard dipole antennas would only see static. |
| The "Null" Problem | Most tactical handhelds and vehicle whips are vertically polarized. If a signal reflects off a slanted roof, it may arrive at your site with a significant horizontal shift. A standard vertical antenna would experience a signal dropout of up to 20 dB. |
| The Tactical Solution | The LP-300-2500 features a flexible mounting arrangement that allows operators to switch between Horizontal and Vertical polarization in seconds. This ensures you can match the orientation of the incoming reflected wave to maintain a stable, high-fidelity intercept. |
| Published detail | To successfully disrupt a target link (e.g., a high-speed LTE data link or a 400 MHz trunked system), you must achieve a superior Jamming-to-Signal (J/S) ratio at the victim’s receiver. |
| Power Density Focus | Instead of scattering 250W in all directions, the LP-300-2500 focuses that energy into a concentrated 65-degree cone. |
| ERP Advantage | This concentration exponentially increases your Effective Radiated Power (ERP). You can successfully "drown out" a legitimate signal from several kilometers away, even when the adversary is using high-power mobile transmitters. |
| The Solution | The LP-300-2500 is D.C. Grounded. It constantly bleeds off this static charge to the mast and earth. This ensures the lowest possible noise floor, allowing you to detect low-power "hidden" transmissions or frequency-hopping signals that would be buried in the static of an ungrounded antenna. |
| Rear-Mount Advantage | Since the mount is at the rear, you can use a standard metal mast without worrying about it distorting your signal. Ensure the mast is at least 51mm (2 inches) in diameter for stability. |
| Microwave Cable Integrity | At 2500 MHz (2.5 GHz), cable loss is severe. Avoid standard RG-58. Use LMR-400 or LMR-600. Every 3 dB of cable loss effectively cuts your jamming power or reception sensitivity in half. |
| Boresight Alignment | Because the beamwidth is 65 degrees, a 30-degree error in alignment will drop your gain significantly. Use a compass to ensure the antenna is pointed exactly at the target sector for maximum intercept probability. |
| Connector Weather-Proofing | Microwave connectors are highly sensitive to moisture. A single drop of water in the N-type connector will cause a massive VSWR spike. Use butyl rubber tape for a primary moisture seal on all outdoor connections. |
| Frequency stated in title | 300-2500 MHz |
| Gain stated in title | 9 dBi |
| Category | Horn, Dish, Grid & Log Periodic |