| Model | LPDP-500-3000 |
| Frequency (manufacturer model field) | 500-3000MHz |
| Bandwidth (manufacturer model field) | 500-3000MHz |
| Gain (manufacturer model field) | 9 dBi |
| Frequency Range | 500-3000 MHz |
| Gain | 9 dBi |
| Bandwidth | 500-3000MHz |
| Polarization | Vertical & Horizontal |
| Input Impedance | 50 Ohms |
| Radiation Pattern | Directional |
| Horizontal Beamwidth -Half Power Points | 70 +/-10 Degrees |
| Front to Back Ratio | 16 +/- 1 dB |
| VSWR - Equal To or Better Then | 2.5:1 |
| RF Power Handling Capacity | 250 Watts |
| Input Termination | 2 x N-Female |
| Lightning Protection | DC Ground |
| Antenna Materials | 6363T6 Aluminum Alloy |
| Mounting Hardware -Materials | Marine Grade Stainless Steel |
| Wind Rating | 200 Km/Hr. |
| Overall Length | 680 mm |
| Shipping Length | 800 mm |
| Support Boom -Material - O.D. | AluminumSquare Tube |
| Elements - Materials- Cross Section - Outer Diameter | AluminumRound Rod |
| Mounting Clamps Position | At rear end of the support boom |
| Maximum Mount Pipe Diameter | 50-76 mm (2-3 Inches) |
| Gross Weight | 5 Kgs. |
| Operating Temperature | (-) 30 to + 70 Degrees Celsius |
| Storage Temperature | (-) 40 to + 80 Degrees Celsius |
| Humidity | 0 to 95% RH |
| Simultaneous E & H Processing | Featuring 2 x N-Female ports, the antenna allows for the concurrent transmission or reception of vertical and horizontal signals, providing total polarization diversity. |
| Aero-Dynamic Radome | The high-tech ABS enclosure is RF-transparent and specifically shaped (cylindrical/tapered) to minimize wind loading and ice formation, ensuring the antenna maintains its 9 dBi gain even in sub-zero or high-velocity wind conditions. |
| No-Loading Integrity | By avoiding loading techniques to reduce size, the LPDA maintains a consistent, high-efficiency radiation pattern across the entire 500-3000 MHz range. |
| Fully Welded Elements | All radiating elements are welded to the support booms to prevent RF inter-modulation and mechanical fatigue. |
| Military Finish | The antenna and radome are finished in MIL-grade Olive Green, with the internal components protected by an epoxy-based powder coating to resist corrosive gases and salt spray. |
| D.C. Grounded Architecture | The system operates at D.C. ground, providing a low-resistance path for lightning protection and ensuring a quiet noise floor for sensitive surveillance equipment. |
| Dual-Polarized Cross-Element Architecture | Simultaneous capture of all signal polarizations. |
| Ruggedized ABS Radome | Protects elements from ice, salt, and wind while remaining aesthetically pleasing. |
| Elite 500–3000 MHz Bandwidth | Covers UHF, GSM, LTE, and S-Band in a single directional unit. |
| High-Efficiency 9 dBi Gain | Focused 65-degree beamwidth for precise signal targeting and monitoring. |
| MIL-STD-810G Certified | Tested for shock, vibration, humidity, fungus, and salt fog. |
| Rear-Mount Installation | Permanently welded mounting fixture facilitates rapid installation on masts up to 52mm. |
| Marine-Grade 316 Fasteners | Ensures total corrosion resistance for coastal and shipboard applications. |
| Internal Cable Protection | Elements and connections are fully enclosed to prevent environmental degradation. |
| D.C. Grounded Shielding | Integrated lightning protection and high noise immunity. |
| The "Null" Problem | A single-polarized antenna will experience deep signal fades (up to 30 dB) when the incoming wave's polarization rotates away from the antenna's orientation. |
| The Diversity Solution | By monitoring the Vertical and Horizontal ports simultaneously, your SIGINT system can perform Maximum Ratio Combining (MRC). When the signal fades on the vertical plane, it almost always "peaks" on the horizontal plane, ensuring a continuous, high-quality intercept of data bursts. |
| Visual Obscuration | The ABS Radome hides the internal element structure. An adversary cannot visually determine if the antenna is currently focused on 500 MHz (large elements) or 3000 MHz (small elements), nor can they see the exact polarization tilt. |
| Environmental Integrity | In high-speed tactical movements, open elements can "whistle" or vibrate, creating a mechanical signature. The tapered radome is acoustically quiet and aerodynamically stable, rated for 200 Km/Hr winds. |
| Published detail | Monitoring the 2.4 GHz (Wi-Fi/ISM) band requires high sensitivity to pick out weak tactical signals among the noise. |
| Low-Noise Floor | The D.C. Grounded design and the protective radome prevent "Precipitation Static" (P-Static). During rain or wind, unshielded antennas build up static charge that raises the noise floor; the LPDP-500-3000 stays "quiet," allowing you to see signals just above the thermal limit. |
| Isolation for Jamming | The 20 dB Cross-Polarization Discrimination allows you to jam a target on one polarization (e.g., Vertical) while simultaneously monitoring the environment on the other (Horizontal) with minimal interference. |
| Published detail | The 65-degree horizontal beamwidth acts as a precision "floodlight" for the 500–3000 MHz band. |
| Target Concentration | Instead of wasting 200W of jamming power in 360 degrees, the LPDP-500-3000 concentrates that energy into a narrow sector. This significantly increases the Jamming-to-Signal (J/S) ratio at the target's receiver. |
| Front-to-Back Protection | The 18 dB F/B ratio is critical for protecting your own team. It ensures that while you are jamming or monitoring a target, your own communication equipment located behind the antenna remains functional and unjammed. |
| Coaxial Selection | At 3000 MHz (3 GHz), cable loss is extreme. Use LMR-600 or higher for runs exceeding 10 meters. A 10-meter run of standard RG-58 would lose nearly 70% of your power. |
| Radome Maintenance | While ABS is rugged, ensure the radome is kept free of metallic paint or heavy carbon-based dirt, which can attenuate the high-frequency 3 GHz signals. |
| Mounting Alignment | Ensure the antenna is mounted level. Because the beamwidth is only 55–65 degrees, a tilt of just 10 degrees can move the "Peak Gain" off the target, reducing your effective range. |
| Connector Sealing | Use professional-grade weatherproofing. In the 3 GHz range, a single drop of water in the N-Female connector will cause a massive VSWR spike and potentially damage your 200W transmitter. |
| Frequency stated in title | 500-3000 MHz |
| Gain stated in title | 9 dBi |
| Category | Radomes, Enclosures & Replacement Parts |